Chain link fence Gate Decorates Yards and Gardens and Protects Your Property

With more and more attention on decorative style and creativity, Chain Link Fence gate is widely used to decorate yards, gardens and to protect their property. The chain link fencing materials are durable and cost low and no maintenance. Chain link gate and gate fittings - specifically the male/female hinges and latch hardware are available in our factory.

Chain Link Fence Gates have five types: Walk Gate, Single Gate, Double Swing Gate, Cantilever Gate and Roll Gate.

Walk Gates is easy to install and widely used. And it can be installed with roll wheel to go in and out conveniently.
Walk Gates can be made to any height and color in both chain link and ornamental. Scrolls are optional for chain mesh gates.

Single Gates can be manufactured for larger openings. Just make sure there is enough room for the gate to open. Single swing gates can be automated.

Double Swing Gates have two leafs and a drop rod to hold them in place while the gate is shut. Double swing gates can be automated.

Cantilever Gates slide open on rollers attached to counterbalance posts. These gates can also be automated and are great for larger openings.

Roll Gates roll on the ground and on a track attached to the fence. These gates cannot be automated and require enough fence space to roll back into.

New order
I am trying to find a source for a gate to fit a 34 foot opening. I would like to use two 17 foot gate to cover this area. One swinging at each side and meet in center . The height needs to be 6 foot.

Black chain link fence and gates technique specifications:

• 1. 2 mt high black powder coated chain link fencing and gates as follows:
  Gate and end posts 40 NB galvanized steel powder coated black.
  Posts 32 NB galvanized steel powder coated black.
  2.4 mt centers.
  Top rail 25 NB galvanized steel powder coated black.
  Attached to posts with black powder coated down fittings Chain Wire galvanized steel black PVC coated, 60 × 60 diamond.
  Bottom cable black PVC coated* 3 sets double gates 25 NB frame powder coated black.
  3. 2 mt opening size, black chain wire infill.
• Gates is swing type, hinged to swing 180 degrees from closed to open,
  complete with frames, latches, stops, keepers, hinges, fabric, braces.
  and PVC coating wire mesh (50 × 50), diameter 4 mm.
• 42 × 42", 42 × 48", 48 × 48", 42 × 60", 42 × 72" single walk Fence gate 1 3/8" tubing hot dipped galvanized.
  12' × 42", 12' × 48", 12' × 60", 12' × 72" double drive fence gate 1 3/8" tubing hot dipped galvanized.
  6' × 6', 6' × 12' kennel panel 1 3/8" tubing hot dipped galvanized.
  Cattle/wrangler panels with bow gate and cattle wrangler panels with hardware attached: 18 gauge or 1.2 mm thick. Galvanized then powder painted brown.
  Tube gates: 18 gauge or 1.2 mm thick. Galvanized then powder painted brown.

How to Make Chain Fence Gates

If you do not want to buy a chain link fence gate and then do it by yourself, install it where you want to install. This is not difficulty things, so you can save a lot of spending.
used in the production process: tape measure, gate Post hinges, gate fork latch, bolts, sockets, wrench, chain links, gate frame, brackets, solder, pliers.

Here are chain link gate installation steps and tips.

• First: under the instructions, make a gate framework and the first part attached on the sliding belt. Then sliding parts are assembled door frame with your hands.
• Second: sliding a rod into the fence and through a coil.
• Third: attach the tension band and slide the second lever into the mesh. Make sure you slide it close enough to the opposite side rail to hold the mesh taut once you attach it to the tension bands.
• Fourth: unhook the strand of mesh that's near the outside second tension bar and pull it out, removing the excess mesh with pliers.
• Fifth: pull the mesh along with tension band tightly while slipping the tension bar into the tension bands on the frame of the gate with pliers, if the net is not tight enough the lever to into go to the next set of loops. Unravel the excess mesh and hook the bar back into the tension bands.
• Final: attach the tie line to the benchmarking of the top and bottom once the mesh is fixed in one place. A Cable line in the mesh around the hook with pliers, pulled the network cable has been slightly higher than the door frame to the network. Ensure let the tie cord around freely in the mesh around with pliers.
• Tips: his metal hardware must be ready to complete. In order to switch the gates must be to the height of the ground.

Our new project of gates and fences

• Double Swing Gate
  Material Steel.
  Surfacing Galvanization with plastic-coating.
  Dimensions Height: 200 cm, Width: 400 cm.
  Frame: 5 cm × 5 cm.
  Vertical bars of 2.5 cm × 2.5 cm, welded at a distance of 10 cm.
  Square posts with cap: 20 cm × 20 cm × 250 cm.
  Hot dip galvanized coating ISO 1461.
• Single Swing Gate
  Material Steel.
  Surfacing Galvanization with plastic-coating.
  Dimensions Height: 200 cm, Width: 100 cm.
  Frame: 4 cm × 4 cm.
  Square mesh of 5 cm × 5 cm, welded into the frame.
  Square posts with cap: 5 cm × 5 cm × 250 cm.
  Hot dip galvanized coating ISO 1461.
• Fences
  Material Steel.
  Surfacing Galvanization with plastic-coating.
  Dimensions Fence height: 200 cm.
  Panel width: 250 cm.
  Height of posts: 250 cm.
  Mesh: 10 cm × 5 cm.
  Hot dip galvanized coating ISO 1461.