Our company provides you standard Chain Link Fence gates, gate posts and other Accessories products for both single and double swing-type gates for industrial and commercial application.
ICSG-01: Galvanized chain link fabric gate used for railway security.
ICSG-02: Chain link fabric gate with barbed tape on top is used for industrial security.
ICSG-03: Three strands of barbed wires are fixed on the top of the chain link fabric fence.
ICSG-04: Chain link mesh and gate framework installation.
Specification of industrial and commercial steel swing gates:
- Material of gate framework: round and rectangular tubular.
- Coating of gate framework and adjoining fence framework: either zinc-coated steel frames or polymer-coated steel frames.
- Top security: three strands of Barbed Wire or barbed tape.
Table 1 Gate Frame Members, Dimensions, and Weights
Gate Fabric Height | Outside Dimension in. (mm) | Minimum Weight lb/ft (kg/m) |
6 ft (1.8 m) or Less |
Round tubular (steel) | 1.66 (42.2) | 1.83 (2.72) |
Rectangular tubular (steel) | 2.00 (50.81) | 2.52 (3.75) |
Over 6 ft (1.8 m) |
Round tubular (steel) | 1.90 (48.3) | 2.28 (3.39) |
Rectangular tubular (steel) | 2.00 (50.8) | 2.52 (3.75) |
Interior Bracing |
Round pipe (steel) | 1.66 (42.2) | 1.83 (3.39) |
Rectangular pipe (steel) | 1.50 (38.1) | 1.84 (2.74) |
Table 2 Typical Dimensions and Weight of Gate Posts
Gate Leaf Width | Material | Outside Diameter of Pipe in. (mm) | Minimum Weight lb/ft (kg/m) |
For Gate Fabric Height of 6 ft (1.8 m) or less |
Up to and including 4 ft. (1.2 m) | Steel | 2.375 (60.3) | 3.11 (4.63) |
Over 4 to 10 ft (1.2 to 3.7 m) | Steel | 2.875 (73.0) | 4.64 (6.91) |
Over 10 to 18 ft (3.7 to 5.5 m) | Steel | 4.000 (101.6) | 6.56 (9.77) |
For Gate Fabric Height Over 6 ft (1.8 m) |
Up to and including 6 ft (1.8 m) | Steel | 2.875 (73.0) | 4.64 (7.04) |
Over 6 to 12 ft (1.8 to 3.7) | Steel | 4.000 (101.6) | 6.56 (9.77) |
Over 12 to 18 ft (3.7 to 5.5 m) | Steel | 6.625 (168.3) | 18.02 (26.83) |
Over 18 to 24 ft (5.5 to 7.3 m) | Steel | 8.625 (219.1) | 27.12 (40.36) |
Gate accessories:
Our company provide you necessary and qualified gate accessories as following:
- Gate hinges we provided has a minimum zinc coating of 1.2 oz/ft2 which permits the gate to swing a full 180°.
- Single gate latch, double gate latch, gate stops and keepers (for each gate leaf over 5 ft wide).
- All gate accessories have a minimum zinc coating of 1.2 oz/ft2.
- All of our gate hardware is of sufficient strength and durability to support the gate and repeated open-close cycles.
Gate assembling:
- Gate frame shall be welded at all corners or assembled with corner fittings.
- For gates assembled with corner fittings, 5/16 in. (7.9 mm) diameter truss rods of the same metal and finish as the gate frames is needed for panels of 5 ft (1.5 m) wide.
- Vertical or horizontal interior bracing of the same metal and finish as the gate frame at maximum intervals of 8 ft is needed if gate leaf chain link fabric's width or height is 8 ft or more.
Top security installing:
- To accommodate the higher height of barbed Wire , the end members of the gate frame should be extended in height.
- For barbed wire, three strands of barbed wire shall be uniformly spaced and the top strand is approximately 1 ft above the gate frame, the maximum intervals among barbed wires attached shall be of 8 ft.
- For barbed tape, the minimum height for barbed tape installed at the top of the automatic gate shall be a minimum of 8 ft.